But I do still have a question.

Having in mind that I trying to limit In and Out traffic by Machine/Host/Ip/Server and that

• I have a bridged DMZ to WAN
• I have rules filtering anything from wan to my servers, I mean all traffic is filtered from the internet to my servers
• I have rules filtering anything going from my servers to the internet

Where exactly should I apply my In/Out rule for my server and in which order? Should it be before any other rules applied to a specific order, or it does not matter?

Thank you,
Alex

Ok please ignore my last message. I've "read" or better said "overlooked" the http://doc.pfsense.org/index.php/Traffic_Shaping_Guide#Limiter for N times, but never like this last time. Until now I was just looking for keywords in that document for what I needed, and didn't read the exact document word by word to fully understand how Limiter works.

I recommend to any1 that will read this, to read again and this time read it not jump from a word to another... so you can understand how Limiter works and how to apply it.

Tnx, jimp.

It's all explained in those other threads. Limiters are what you need to do this.

http://doc.pfsense.org/index.php/Traffic_Shaping_Guide#Limiter

Ok, that is where I get to... I have understood that Limiters will give me what I need, I have been trying/testing it but with no success. What I need is a guide of how to apply them. I just want some guidances, no matter if is a 500 pages book or whatever.

Hope some1 could guide me through this so I can understand better how to work with it.

Tnx,
Alex

Salutare voua, sunt si eu un alt utilizator al PfSens-ului (1.2.3 si 2.0)

Vin sa cer si eu ajutorul/sfatul vostru in legatura cu faptul de a limita traficul de iesire si intrare pentru fiecare server care il administrez, vreau sa stiu si eu ce imi recomandati si cum as putea sa duc la indeplinire acest lucru.

Va atasej o poza unde am facut o mica schita cu structura care o am acum.

Edit:
Am uitat sa specific caci nu folosec nat 1:1 pentru serverele mele, ci un bridge intre DMZ si WAN

Buenos dias a todos y gracias por el aporte que estais dando.

Yo tengo este siguiente escenario y necesito aplicarle restricciones de trafico para cada una de mis maquinas, sea cual sea el metodo... lo necesito. Se me olvido especificar en la foto adjuntada que tengo Bridge entre DMZ y WAN y no uso NAT 1:1.

Espero que me podeis ayudar.


PfSense 2.0 uso

no1 nada?

[2.0-RC1 (amd64) built on Sat Feb 26 18:07:23 EST 2011]

Forgot to mention that my version is:

2.0-RC1 (amd64)
built on Sat Feb 26 18:07:23 EST 2011

[How could I limit traffic for each and 1 of my servers (upload and download)?]

Hello folks, I am here to ask you for your help to my problems.

I have this next scenario and I need to limit the bandwidth for my servers on a bridged interface. Here it goes

Code:

                         |LAN| ----> Laptop

~~~~~              
~iNet~   ----->   |WAN|
~~~~~                  || -->Bridge DMZ to WAN
                         |DMZ|----
                                      |
                   ------------------------------------
                   |                       |                    |
                ---------         ----------        -----------    ....
                Server1       Server2            Server3

So, having that representation now I ask you:
How could I limit traffic for each and 1 of my servers (upload and download)?

I've been trying to do it following this tutorial, but with no success.
http://forum.pfsense.org/index.php?topic=28002.0

I have also read this message that got me even more confused
http://forum.pfsense.org/index.php/topic,1384.msg8196.html#msg8196

So please help me understand all this Traffic Shaping.

Thank you

Edit:
An image representing my structure