Netgate SG-1000 microFirewall

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - ghkrauss

Pages: [1] 2 3 4 5 6
1
Hardware / Trim Assistance
« on: January 24, 2018, 11:33:18 am »
Fellow members:

I have Pfsense 2.4.2_1 running with a Samsung 850 Pro (256Gb). I have tried follow the commands and process for turning on Trim but have not been successful.

I obtained the SSD drive information as the following:

/dev/gptid/45a16a44-0122-11e8-a969-001b218d29b8   /


What sequence of commands is required to turn on Trim.

I typed tunefs -p / at the command prompt and the system indicates Trim is disabled.

Any assistance would be appreciated.

Thank You

2
Hardware / Swap File
« on: January 21, 2018, 08:58:00 am »
Fellow Members:

What is the command to turn off the swap file in Pfsense 2.4.2 as I am installing a SSD.

Thanks for any assistance!

Best Regards

3
Installation and Upgrades / Pfsense 2.4.2
« on: December 11, 2017, 09:19:30 am »
Gentlemen:

Does Pfsense 2.4.2 have "TRIM" tuned on by default when installing the image?

4
Hardware / Intel NIC
« on: September 26, 2017, 10:11:18 am »
Has anyone used the following Intel network card successfully with Pfsense 2.4.0 RC

Intel PRO/1000 VT Quad Port Server

Many thanks for any input. From the hardware compatibilty specifications it should work.

5
Hardware / Intel pro 100 /Vt - Pfsense
« on: July 14, 2017, 09:58:04 am »
Hello folks:

Any experience with the Intel pro 1000 /VT on Pfsense? Based on the document it should work. Thanks for any feedback.

6
Traffic Shaping / fd_codel
« on: May 25, 2017, 10:33:48 am »
Are these any definitive plans or time table for implementing fd_codel for traffic shaping in Pfsense 2.4 or later versions?

7
General Questions / Hard Drive Noise
« on: May 23, 2017, 06:44:36 pm »
Hello:

I have a Western Digital Drive 250 GB (10K) installed in the Pfsense system. It passes the  smart drive test but makes a strange squeaking sound even when the system has minimal load. Must be the drive. Also hear a low muffled grinding sound at times. Any one ever had this issue?

8
2.4 Development Snapshots / Pfsense 2.4 ZFS File System
« on: October 29, 2016, 01:37:25 pm »
What will be the hardware requirements for utilizing the ZFS file system?

9
DHCP and DNS / DNS Resolver Question
« on: October 18, 2016, 07:20:51 am »
When using the DNS resolver if other DNS servers are listed (ie Google IPv4 and IPv6) what is the impact? Does the DNS Resolver still go the to the DNS Root servers to start the resolution process.

10
DHCP and DNS / DNS Resolver IPV6 Resolution Question
« on: October 16, 2016, 11:37:37 am »
In order to resolve and IPV6 website I had to list and IPV6 upstream DNS (ie Google). Is this the correct configuration? Absent the IPV6 DNS enrty in the Pfsense setup I just resolve to the IPV4 address.

11
Installation and Upgrades / Pfsense 2.3.2_1 Increased Memory Usage
« on: October 08, 2016, 10:54:20 am »
After updating to Pfsense 2.3.2_1 from Pfsense 2.3.2 the memory usage increased about 5%  as noted for the main display control panel. Any one else note this increase? All otherfunctions are without error or problems.

12
Installation of Suricata 3.1.1 with Pfsense 2.4 failed. It consistently reported errors. Any one notice this issue. attached below is the crash report.

13
IDS/IPS / Pfsense 2.4 Suricata 3.1.1 Cash Report
« on: September 23, 2016, 12:51:02 pm »
Cash report Pfsense 2.4 with Suricata 3.1.1

The latest Suricata package can not load without errors. Some code is missing.

14
IDS/IPS / Suricata 3.1.1
« on: August 31, 2016, 04:39:03 pm »
Any news on the eventual launch of Suricata 3.1.1 for Pfsense 2.3.2?

15
IDS/IPS / Netcore inbound Hacks Attempt
« on: July 26, 2016, 07:37:57 am »
I am noticing a blizzard of Netcore Router hack attacks that have been flagged by Suricata. Never seen this many in the past. Anyone else seeing this situation?

Pages: [1] 2 3 4 5 6