Netgate SG-1000 microFirewall

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ghkrauss

Pages: [1] 2 3 4 5 ... 10
1
Hardware / Re: Trim Assistance
« on: January 25, 2018, 11:09:38 am »
Fellow Member:

Thanks for the assistance. The steps you outlined worked perfectly. The single user boot was the key.

Howard

2
Hardware / Re: Trim Assistance
« on: January 24, 2018, 03:37:25 pm »
Thanks for the suggestion. Still can not get Trim to enable.

3
Hardware / Trim Assistance
« on: January 24, 2018, 11:33:18 am »
Fellow members:

I have Pfsense 2.4.2_1 running with a Samsung 850 Pro (256Gb). I have tried follow the commands and process for turning on Trim but have not been successful.

I obtained the SSD drive information as the following:

/dev/gptid/45a16a44-0122-11e8-a969-001b218d29b8   /


What sequence of commands is required to turn on Trim.

I typed tunefs -p / at the command prompt and the system indicates Trim is disabled.

Any assistance would be appreciated.

Thank You

4
Hardware / Re: Swap File
« on: January 21, 2018, 06:48:35 pm »
John:

I have 16Gb as there are a number of packages running and a large wireless AP group.

Howard

5
Hardware / Re: Swap File
« on: January 21, 2018, 10:48:27 am »
Thanks John. I will take your advice. Installing a Samsung 850 Pro.

Best Regards,

Howard

6
General Discussion / Re: Win10 vlans working finally
« on: January 21, 2018, 09:26:06 am »
Glad you have installed the new Intel driver for Windows 10. I have tried but the MS operating system (Windows 10) will not allow installation. What was your configuration procedure. I would also like to use Window 10 with vlans.

Thanks for the assistance
Howard

7
Hardware / Swap File
« on: January 21, 2018, 08:58:00 am »
Fellow Members:

What is the command to turn off the swap file in Pfsense 2.4.2 as I am installing a SSD.

Thanks for any assistance!

Best Regards

8
Installation and Upgrades / Pfsense 2.4.2
« on: December 11, 2017, 09:19:30 am »
Gentlemen:

Does Pfsense 2.4.2 have "TRIM" tuned on by default when installing the image?

9
Hardware / Intel NIC
« on: September 26, 2017, 10:11:18 am »
Has anyone used the following Intel network card successfully with Pfsense 2.4.0 RC

Intel PRO/1000 VT Quad Port Server

Many thanks for any input. From the hardware compatibilty specifications it should work.

10
Hardware / Re: Intel pro 100 /Vt - Pfsense
« on: July 15, 2017, 05:52:16 am »
Thank you for the update. I was given this NIC and thought I would investigate the situation. I have another operating Intel NIC in production but might try the Intel Pro 100 / VT and see if it will operate in that environment.

11
Hardware / Intel pro 100 /Vt - Pfsense
« on: July 14, 2017, 09:58:04 am »
Hello folks:

Any experience with the Intel pro 1000 /VT on Pfsense? Based on the document it should work. Thanks for any feedback.

12
Traffic Shaping / fd_codel
« on: May 25, 2017, 10:33:48 am »
Are these any definitive plans or time table for implementing fd_codel for traffic shaping in Pfsense 2.4 or later versions?

13
General Questions / Re: Hard Drive Noise
« on: May 24, 2017, 11:01:27 am »
Thanks for the feedback on the hard drive. I have just ordered a new drive. It seems many of the items that are shipped as new really have issues. I am just striving for reliability!


Best to All

Howard

14
General Questions / Hard Drive Noise
« on: May 23, 2017, 06:44:36 pm »
Hello:

I have a Western Digital Drive 250 GB (10K) installed in the Pfsense system. It passes the  smart drive test but makes a strange squeaking sound even when the system has minimal load. Must be the drive. Also hear a low muffled grinding sound at times. Any one ever had this issue?

15
2.4 Development Snapshots / Pfsense 2.4 ZFS File System
« on: October 29, 2016, 01:37:25 pm »
What will be the hardware requirements for utilizing the ZFS file system?

Pages: [1] 2 3 4 5 ... 10