pfSense Support Subscription

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ikkuranus

Pages: [1] 2 3
Firewalling / Re: Floating rules, Plex, and redirected ports
« on: November 09, 2017, 01:53:20 pm »
I don't have a solution for you but you might wish to change plex settings locally instead of using the site as that would mean all changes are updated immediately.

General Discussion / Re: "Fanboy" series - IPv6 and NATs - YouTube
« on: October 02, 2017, 11:07:04 pm »
I hate that style of video they are annoying as hell.

Installation and Upgrades / Re: SG-2220 - Lost Password
« on: July 12, 2017, 04:57:23 am »

If you haven't password protected the console you can simply reset the password from here.

If you have password protected the console you will need to follow these steps:

Reboot the pfSense box
Choose option 4 (Single User Mode) from the loader menu (The one with the ASCII pfSense logo)
Press enter when prompted to start /bin/sh
Remount the drive as rewritable:

/sbin/mount -o rw /
Run the built-in password reset command:

Follow the prompts to reset the password

Installation and Upgrades / Re: cant install on my UPSquared
« on: July 11, 2017, 11:24:52 am »
Try the 2.4 beta.

« on: July 03, 2017, 04:06:53 am »
Pfsense by default doesn't set any quotas or speed limits so it's most likely your server.
I'd start by looking at the PHP configuration assuming it uses that.

Hardware / Re: Hardware recommendation for home use
« on: June 10, 2017, 01:38:18 am »
That's fairly mediocre as far as fiber connections go. I'd try it before buying something.

Wireless / Re: Difficulty setting up WLAN
« on: May 21, 2017, 01:26:13 am »
I'd be willing to bet you can't use an internal wireless adapter as an access point with a virtual pfsense unless using pcie passthrough.

Firewalling / Re: Cannot upload files or do upload tests
« on: May 13, 2017, 09:09:06 am »
I'd venture to guess it probably has something to do with having both the wan and lan on the same subnet.
Also you really should put the asus modem/router into bridge mode and avoid that double nat.


Netgear CM600
Dell Powerconnect 5324
RPI3 Raspbx

Recently swapped out my cable modem for a Netgear CM600 (so far my connection seems way better no more jitter or people complaining about voice calls being garbled/cutting out) Next week I'm getting an UPS and I plan to use what's left of that flex hose to tidy up the power cables.

Hardware / Re: How Many Users can be connected
« on: April 27, 2017, 12:59:42 am »
The closest thing they have to a non-free version would be what is included with official hardware (specifically the sg devices that come preinstalled with pfsense) From what I understand the only difference is a few packages that aren't included with the community version and it's branded slightly different from the community edition. The community edition does not impose any artificial limits.

Hardware / Re: I have only one WAN interface after installation
« on: April 14, 2017, 03:56:06 pm »
Any interface can be defined as a wan. Just create a gateway and assign it to the interface or ip4 / 6 configuration set to dhcp / pppoe depending on connection type.

Hardware / Re: Android USB Tether via USB and Hyper-V
« on: December 14, 2016, 03:15:13 pm »
I had the same issue but the major difference was I used a raspberry pi to create an ethernet bridge. If I hooked up the pi bridge directly to the switch all was good but trying to use it as a wan for pfsense just never worked at all.

Hardware / Re: SG-1000 microFirewall Optical Illusion
« on: October 01, 2016, 04:06:36 pm »
This may be an excellent box to run Asterisk on.

I suppose if you like to edit the config files by hand. I say this because you wont have enough ram to use freepbx without it paging constantly. Actually I'm thinking of the pogoplugs 128MB of ram that's insuffucient so I guess 512 would be enough but it still seems a bit expensive for this purpose. A rpi3 is superior and cheaper. The only advantage this thing has is disk on module which I'm unsure if it's more reliable then flash memory or not.
The second nic don't really serve any purpose for asterisk.

ms firewall blocks ping and pretty much everything else from other subnets.

I have added some permissions so people with more limited accounts can print out vouchers without having full access to the webui

compatible with 2.3.x not sure about older versions
unzip the following file into /etc/inc/priv/

@DanieleIT feel free to add this as part of the package.

Pages: [1] 2 3