pfSense Support Subscription

Author Topic: pdsbm-ln2 1U server Lan Ports fail in RC canidate. Using Intel 82573 nic  (Read 10744 times)

0 Members and 1 Guest are viewing this topic.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
No problems for a year or more in pfsense with this server running pfsense till 2.2 beta just installed yesterday.. Now em1 is gone and em0 shows up but is not showing connection.   My server has the pdsbm-ln2 mother board in it.  It has the Intel 82573 nic built in.. 2 ports.  This is supported with freebsd 10 from what I read. 

Any one else use this nic or this motherboard and have 2.2 working?  I am usually pretty good at getting things going. but this not figured out yet. maybe needs to be forced on or something.
« Last Edit: December 13, 2014, 11:28:34 pm by Topper727 »
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline cmb

  • Hero Member
  • *****
  • Posts: 11230
  • Karma: +893/-7
    • View Profile
    • Chris Buechler
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #1 on: December 04, 2014, 12:26:35 am »
That really sounds like a hardware problem. Try the version you were on before.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #2 on: December 04, 2014, 11:46:25 am »
It was working just fine one 2.1 but the update to beta 2.2 is when it failed.  Later tonight after work I will try putting back the older version and my guess it will work just fine.  I have since factory reset the system just to take that question out of the mix.  I know it is not as good as clean reinstinstall.

I am now using 1 net port and that is Wan so I get in that way and updated to 2.2 december 3rds build.. still nothing. Will let you know what I find. I will figure it out
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #3 on: December 05, 2014, 12:10:57 pm »
I just managed to get a 2.2 beta on December 4th to burn to cd and installed that fresh.. It Shows only EM0.   But I have tried 2 other linux distro's that both show em0 and em1.    I don't have another blank cd to burn 2.1 yet.  So that test can not be done at this current moment.
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #4 on: December 05, 2014, 07:50:59 pm »
Ok .. I got a 2.1 iso on cd and tried it.  I got em0 em1 and usbus00,10,20,30,40 all up status.  But the 2.2 Beta as of dec 4th cd just shows em0
   
So ubuntu and 2.1 see the ports fine but 2.2 does not. I am running off CD so no chance of any of my changes or things can conflict with this.. This is a clean test of 2.1 aug 24th release and 2.2 dec4th Beta ..

 My server has the pdsbm-ln2 mother board in it.  It has the Intel 82573 nic built in.. 2 ports.   


Summary

2.1 release
em0 and em1 work

2.2 beta dec 4th
em0 ok
em1 gone

All tests using Live CD images only

« Last Edit: December 05, 2014, 09:51:49 pm by Topper727 »
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #5 on: December 05, 2014, 10:49:10 pm »
also in hopes of trying to get some use of 2.2 I have a Intel 82546 dual nic card.. This works fine in 2.1.5 64bit but locks the 2.2 beta in the booting.

screen 1st capture is of 2.1.5 64 bit running on a CDRom. 

screen 2nd capture is of 2.2 64 dec 4th running on CDRom failing at this point staying locked
« Last Edit: December 05, 2014, 11:01:52 pm by Topper727 »
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline stephenw10

  • Administrator
  • Hero Member
  • *****
  • Posts: 11914
  • Karma: +468/-15
    • View Profile

Offline charliem

  • Sr. Member
  • ****
  • Posts: 565
  • Karma: +43/-1
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #7 on: December 06, 2014, 09:31:54 am »
I don't think MSI will fix it; the resources can't even be allocated.

Seems to have started in freebsd 9.2: https://groups.google.com/forum/#!topic/mailing.freebsd.current/AePu1kitjLY  Not sure if that patch ever made it into 9.3 or 10.1, or if that was even the proper fix.

Offline stephenw10

  • Administrator
  • Hero Member
  • *****
  • Posts: 11914
  • Karma: +468/-15
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #8 on: December 06, 2014, 09:45:22 am »
Could be two different issues here. One NIC type fails to attach, the other crashes the boot.
Could we see a complete boot log, /var/log/dmedg.boot, from 2.2 with only the 2 on-board NICs?

Steve

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #9 on: December 06, 2014, 09:48:06 pm »
ok here is the log file you requested.. I am using a usb to lan 100 adapter right now to get me access to use 2.2 beta 64


Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.1-RELEASE #0 29f4af5(releng/10.1)-dirty: Thu Dec  4 08:55:34 CST 2014
    root@pfsense-22-amd64-builder:/usr/obj.amd64/usr/pfSensesrc/src/sys/pfSense_SMP.10 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Pentium(R) Dual  CPU  E2200  @ 2.20GHz (2194.55-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x6fd  Family = 0x6  Model = 0xf  Stepping = 13
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant, performance statistics
real memory  = 4294967296 (4096 MB)
avail memory = 4088520704 (3899 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <INTELB R_WATERP>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80606640, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff806066f0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff806067a0, 0) error 1
iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff8062de10, 0) error 1
iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff8062dec0, 0) error 1
iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi/.
iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff8062df70, 0) error 1
random: <Software, Yarrow> initialized
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
acpi0: <PTLTD   RSDT> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x30c0-0x30c7 mem 0xd0000000-0xd00fffff,0xc0000000-0xcfffffff irq 16 at device 2.0 on pci0
agp0: <Intel 946GZ SVGA controller> on vgapci0
agp0: aperture size is 256M, detected 7676k stolen memory
vgapci0: Boot video device
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pcib1: failed to allocate initial I/O port window: 0-0xfff
pcib1: failed to allocate initial memory window: 0-0xfffff
pcib1: failed to allocate initial prefetch window: 0-0xfffff
pci2: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pcib2: failed to allocate initial memory window: 0xd0100000-0xd01fffff
pci6: <ACPI PCI bus> on pcib2
em0: <Intel(R) PRO/1000 Network Connection 7.4.2> port 0x4000-0x401f irq 16 at device 0.0 on pci6
em0: Using an MSI interrupt
em0: Setup of Shared code failed
device_attach: em0 attach returned 6
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pcib3: failed to allocate initial memory window: 0xd0200000-0xd02fffff
pci7: <ACPI PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection 7.4.2> port 0x5000-0x501f irq 17 at device 0.0 on pci7
em0: Using an MSI interrupt
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0x3000-0x301f irq 16 at device 29.0 on pci0
usbus0 on uhci0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0x3020-0x303f irq 17 at device 29.1 on pci0
usbus1 on uhci1
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0x3040-0x305f irq 18 at device 29.2 on pci0
usbus2 on uhci2
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0x3060-0x307f irq 19 at device 29.3 on pci0
usbus3 on uhci3
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xd0500000-0xd05003ff irq 16 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib4
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x30a0-0x30af at device 31.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0x30f0-0x30f7,0x30e4-0x30e7,0x30e8-0x30ef,0x30e0-0x30e3,0x30b0-0x30bf mem 0xd0500400-0xd05007ff irq 17 at device 31.2 on pci0
ata2: <ATA channel> at channel 0 on atapci1
ata3: <ATA channel> at channel 1 on atapci1
acpi_button0: <Power Button> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcafff,0xcb000-0xcbfff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen2.1: <Intel> at usbus2
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen1.1: <Intel> at usbus1
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen4.1: <Intel> at usbus4
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen3.1: <Intel> at usbus3
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
ada0 at ata2 bus 0 scbus1 target 0 lun 0
ada0: <ST3250310AS 3.AAF> ATA-7 SATA 1.x device
cd0 at ata2 bus 0 scbus1 target 1 lun 0
cd0: <TSSTcorp CDDVDW TS-H653N 0208> Removable CD-ROM SCSI-0 device
cd0: 150.000MB/s transfers (SATA 1.x, UDMA2, ATAPI 12bytes, PIO 8192bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
ada0: Serial Number 6RYAJH0Y
ada0: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
ada0: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1097273320 Hz quality 1000
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub3: 8 ports with 8 removable, self powered
Root mount waiting for: usbus4
ugen4.2: <vendor 0x0409> at usbus4
uhub5: <vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2> on usbus4
Root mount waiting for: usbus4
uhub5: 4 ports with 4 removable, self powered
ugen4.3: <vendor 0x0b95> at usbus4
axe0: <vendor 0x0b95 product 0x7720, rev 2.00/0.01, addr 3> on usbus4
Root mount waiting for: usbus4
ugen4.4: <Microsoft> at usbus4
ukbd0: <Microsoft Natural Ergonomic Keyboard 4000, class 0/0, rev 2.00/1.73, addr 4> on usbus4
miibus0: <MII bus> on axe0
ukphy0: <Generic IEEE 802.3u media interface> PHY 16 on miibus0
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
kbd2 at ukbd0
ue0: <USB Ethernet> on axe0
uhid0: <Microsoft Natural Ergonomic Keyboard 4000, class 0/0, rev 2.00/1.73, addr 4> on usbus4
Root mount waiting for: usbus4
Trying to mount root from ufs:/dev/ada0s1a [rw]...
ugen3.2: <Crystalfontz America> at usbus3
umodem0: <Crystalfontz America CFA-735 Display, class 2/0, rev 2.00/2.00, addr 2> on usbus3
umodem0: data interface 1, has no CM over data, has no break
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #10 on: December 06, 2014, 10:10:45 pm »
Posted by: stephenw10
on: Today at 07:46:29 am Insert Quote
Try disabling msi/msi-x:
https://doc.pfsense.org/index.php/Tuning_and_Troubleshooting_Network_Cards#MSI.2FMSIX

Tried this and nothing changed at all.. still only 1 built on lan port works.  This is not too much of problem right at moment cause I am using not fast internet so my USB - LAN 100 works ok for the slow speed.  But I plan to get much faster and I need the 1gig built on to work
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline stephenw10

  • Administrator
  • Hero Member
  • *****
  • Posts: 11914
  • Karma: +468/-15
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #11 on: December 07, 2014, 09:05:45 am »
Did you have that enabled during the above boot? I still see:
Code: [Select]
em0: Using an MSI interrupt
Steve

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #12 on: December 07, 2014, 12:49:44 pm »
yes, I had that still the default on and after sending that log then I changed it in crossed fingers it might work.  but did not
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.

Offline stephenw10

  • Administrator
  • Hero Member
  • *****
  • Posts: 11914
  • Karma: +468/-15
    • View Profile

Offline Topper727

  • Full Member
  • ***
  • Posts: 245
  • Karma: +25/-0
    • View Profile
Re: pdsbm-ln2 1U server Lan Ports fail in beta
« Reply #14 on: December 07, 2014, 09:38:46 pm »
So wonder how to get this dual nic to show 2 nics not just 1 in pfsense 2.2?
Dell 2950 g3 server
Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Current: 2000 MHz, Max: 2667 MHz
8 CPUs: 2 package(s) x 4 core(s)
8152 MiB and 600meg 10k drive
Pfsense 2.4 .. Hoping to get the phpvirtualbox going again.