Netgate m1n1wall

Author Topic: Dell SC440  (Read 5501 times)

0 Members and 1 Guest are viewing this topic.

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Dell SC440
« on: June 11, 2008, 08:20:43 pm »
I just rebuilt and restored my firewall  :D.  Needed the hard drive out of it.  It did not see the onboard broadcom card.  I thought it was supported under the 6.2 operating system  ????  Anybody got any thoughts?

Offline wallabybob

  • Hero Member
  • *****
  • Posts: 5262
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #1 on: June 12, 2008, 04:50:13 am »
Its disabled in the BIOS?

Its broken?

Its not supported in FreeBSD 6.2?

The appropriate driver recognises it but fails to attach due to some other error?

How about posting the dmesg output so we can see if the device is even seen on startup?
« Last Edit: June 12, 2008, 05:28:07 am by wallabybob »

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #2 on: June 12, 2008, 08:40:33 pm »
let me know what to post and how to post it.
RC

Offline wallabybob

  • Hero Member
  • *****
  • Posts: 5262
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #3 on: June 13, 2008, 05:42:16 am »
Login on the pfsense console, give the command
Code: [Select]
# dmesgcapture the output and put in into a reply to this note.

Apologies if you don't need this level of detail: Alternatively, at the pfSense shell prompt give the command
Code: [Select]
# dmesg > dmesg.txtwhich will write the startup output to the file dmesg.txt which you can then transfer to another system, open the file in an editor, select the whole contents of the file and copy it to the paste buffer then in a web browser start a reply to this note and paste the contents of the paste buffer into the reply.

But maybe this is not necessary. A quick google search turned up the observation that the SC440 includes the Broadcom 5754 NIC. A check of the FreeBSD cvs log for if_bge.c (driver for many of the Broadcom gigE chips) showed the change to support the 5754 in FreeBSD 6.x was committed March 2007. From memory, FreeBSD 6.2 (base code for pfSense 1.2) was released Jan 2007. I suspect you will need to use a FreeBSD 6.3 based version of pfSense - see http://forum.pfsense.org/index.php/topic,9780.0.html for a location where you can probably pick up a pFsense based on FreeBSD 6.3.


Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #4 on: June 13, 2008, 11:10:37 pm »
$ dmesg
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p11 #0: Sun Feb 24 16:49:14 EST 2008
    sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense_SMP.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) D CPU 3.00GHz (2992.52-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf65  Stepping = 5
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe49d<SSE3,RSVD2,MON,DS_CPL,EST,CNTX-ID,CX16,<b14>,<b15>>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 1072152576 (1022 MB)
avail memory = 1035776000 (987 MB)
ACPI APIC Table: <DELL   B8K    >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <DELL B8K    > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib3
bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem 0xefcf0000-0xefcfffff irq 16 at device 0.0 on pci3
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:10:18:2d:d8:3d
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci4: <ACPI PCI bus> on pcib4
pci4: <network, ethernet> at device 0.0 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 21 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 22 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 23 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xff980800-0xff980bff irq 21 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: waiting for BIOS to give up control
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <PCI-PCI bridge> at device 2.0 on pci5
pci6: <PCI bus> on pcib6
fxp0: <Intel 82558 Pro/100 Ethernet> port 0xccc0-0xccdf mem 0xe8001000-0xe8001fff,0xef600000-0xef6fffff irq 18 at device 4.0 on pci6
miibus1: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus1
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:03:47:96:fd:20
fxp1: <Intel 82558 Pro/100 Ethernet> port 0xcce0-0xccff mem 0xe8000000-0xe8000fff,0xef700000-0xef7fffff irq 19 at device 5.0 on pci6
miibus2: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus2
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: 00:03:47:96:fd:21
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xd800-0xd8ff mem 0xef9eff00-0xef9effff irq 16 at device 4.0 on pci5
miibus3: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus3
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re0: Ethernet address: 00:18:e7:15:f2:f1
re0: [FAST]
pci5: <display, VGA> at device 7.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf mem 0xeffffc00-0xefffffff irq 20 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
speaker0: <PC speaker> port 0x61 on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xcafff,0xcb000-0xcbfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: Dell Dell USB Keyboard, rev 1.10/2.00, addr 2, iclass 3/1
kbd2 at ukbd0
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 38204MB <SAMSUNG SP0411N TW100-08> at ata0-master UDMA100
acd0: CDROM <PBDS CD-ROM DH-48N1P/AD11> at ata0-slave UDMA33
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
bge0: link state changed to UP
fxp0: link state changed to DOWN
fxp1: link state changed to DOWN
re0: link state changed to UP
re0: link state changed to DOWN
bge0: link state changed to DOWN
bridge0: Ethernet address: fa:f3:71:47:ef:17
fxp0: promiscuous mode enabled
re0: promiscuous mode enabled
fxp1: promiscuous mode enabled
re0: link state changed to UP
bge0: link state changed to UP
pflog0: promiscuous mode enabled
WARNING: pseudo-random number generator used for IPsec processing
ukbd0: at uhub3 port 1 (addr 2) disconnected
ukbd0: detached


Here is the dmesg results.
RC

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #5 on: June 14, 2008, 12:19:33 am »
The Onboard Interface is enabled.  I connected a network cable to that interface.  It came up at a GB.  I still could not see it under PFSense.  However by connecting that interface I could ping from the firewall back to workstations on the network.  Workstations on the network could no longer get out on the internet or recieve DHCP addresses from the firewall.

I have two broadcom adapters (1 on-board; 1 -pci - x), I can only see one of the two.  The on-board is unaccessible.  I removed the dual intel 100 mb adapter from the server.

It was almost like the on-board and the pci-x card where on the same ireq or using the same resource.

RC

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #6 on: June 14, 2008, 12:24:17 am »
How can I upgrade from 6.2 to 6.3 without a system reinstall.

RC

Offline wallabybob

  • Hero Member
  • *****
  • Posts: 5262
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #7 on: June 14, 2008, 04:51:14 am »
Quote
The Onboard Interface is enabled.  I connected a network cable to that interface.  It came up at a GB. 
How did you tell it came up at a GB? ifconfig?

Quote
I still could not see it under PFSense. 
Where did you go looking for the interface? ifconfig command to pfSense shell? pfSense web gui? Have you run into the problem I described at http://forum.pfsense.org/index.php/topic,9101.0.html

Quote
However by connecting that interface I could ping from the firewall back to workstations on the network.
Well, something has seen that interface and initialised it. I presume you mean the ping reported a response. In that case the onboard interface has been assigned an IP address so its been configured.
Quote
Workstations on the network could no longer get out on the internet or recieve DHCP addresses from the firewall.

I have two broadcom adapters (1 on-board; 1 -pci - x), I can only see one of the two.  The on-board is unaccessible.  I removed the dual intel 100 mb adapter from the server.
You say the onboard NIC is unaccessible BUT you also appear to say the onboard interface sees a ping response which also means it has been initialised and configured with an IP address so it must be "significantly accessible" even if its not accessible in the way you expect.

Quote
It was almost like the on-board and the pci-x card where on the same ireq or using the same resource.

PCI devices are intended to be able to share IRQs.

The dmesg shows a Broadcom NIC and a RealTek NIC as well as two Intel fxp NICs. Where does the RealTek come from - you haven't previously mentioned it?  The dmesg shows 4 NICs: bge0 (a Broadcom), re0 (a RealTek),
fxp0 and fxp1 (Intel 10/100 NICS). If this is the right number of NICs then maybe you haven't seen the 2nd Broadcom because its actually a RealTek?


Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #8 on: June 14, 2008, 10:45:05 am »
Currently have a total of 5 adapters. 

listed Here in order:
onboard - non fuctional
pci-x - broadcomm GB (conection to DSL modem)
dual port intel - removed from configuration(was using for testing but decided to remove
realtek - GB adapter connection LAN

If I remove the pci-x adapter and leave the realtek adapter the pc only see's one adapter.

pfsense is awesome.  I have been having no issue but would love to get the system down to minimum needed hardware.  Even concidering using the onboard power off and power on controls so that I can save on utilities.
RC

Offline cmb

  • Administrator
  • Hero Member
  • *****
  • Posts: 6333
  • Karma: +0/-0
    • LinkedIn
    • Twitter
    • View Profile
    • Chris Buechler
Re: Dell SC440
« Reply #9 on: June 14, 2008, 12:41:57 pm »

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #10 on: June 14, 2008, 10:18:59 pm »
I just got 6.3 and the installed and up and running.  It looks good.  I now have a total of 5 possible interfaces.  I have 3 interfaces diasabled.  I am running on the two broadcom adapters.  They seem to be running great.

Still running some tests.  Snort and DSPAM are not running correctly, still working on those issues.

Over all it looks real good.
RC

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #11 on: June 14, 2008, 10:23:07 pm »
here is the dmesg from 6.3.
RC

$ dmesg
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-RELEASE-p1 #0: Wed Apr  9 23:49:10 EDT 2008
    sullrich@freebsd6-esx.geekgod.com:/usr/obj.pfSense/usr/src/sys/pfSense_SMP.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) D CPU 3.00GHz (2992.52-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf65  Stepping = 5
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe49d<SSE3,RSVD2,MON,DS_CPL,EST,CNXT-ID,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 1072152576 (1022 MB)
avail memory = 1035771904 (987 MB)
ACPI APIC Table: <DELL   B8K    >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Apr  9 2008 23:48:48)
acpi0: <DELL B8K    > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci3: <ACPI PCI bus> on pcib3
bge0: <Broadcom BCM5750 C1, ASIC rev. 0x4201> mem 0xefcf0000-0xefcfffff irq 16 at device 0.0 on pci3
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:10:18:2d:d8:3d
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci4: <ACPI PCI bus> on pcib4
bge1: <Broadcom BCM5754/5787 A2, ASIC rev. 0xb002> mem 0xefbf0000-0xefbfffff irq 17 at device 0.0 on pci4
miibus1: <MII bus> on bge1
brgphy1: <BCM5787 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: Ethernet address: 00:1a:a0:24:fa:80
uhci0: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 21 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 22 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 23 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xff980800-0xff980bff irq 21 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: waiting for BIOS to give up control
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <PCI-PCI bridge> at device 2.0 on pci5
pci6: <PCI bus> on pcib6
fxp0: <Intel 82558 Pro/100 Ethernet> port 0xccc0-0xccdf mem 0xe8001000-0xe8001fff,0xef600000-0xef6fffff irq 18 at device 4.0 on pci6
miibus2: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus2
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:03:47:96:fd:20
fxp1: <Intel 82558 Pro/100 Ethernet> port 0xcce0-0xccff mem 0xe8000000-0xe8000fff,0xef700000-0xef7fffff irq 19 at device 5.0 on pci6
miibus3: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus3
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: Ethernet address: 00:03:47:96:fd:21
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xd800-0xd8ff mem 0xef9eff00-0xef9effff irq 16 at device 4.0 on pci5
miibus4: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> on miibus4
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:18:e7:15:f2:f1
re0: [FAST]
pci5: <display, VGA> at device 7.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfecf mem 0xeffffc00-0xefffffff irq 20 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
speaker0: <PC speaker> port 0x61 on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xcafff,0xcb000-0xcbfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: Dell Dell USB Keyboard, rev 1.10/2.00, addr 2, iclass 3/1
kbd2 at ukbd0
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
hptrr: no controller detected.
ad0: 38204MB <SAMSUNG SP0411N TW100-08> at ata0-master UDMA100
acd0: CDROM <PBDS CD-ROM DH-48N1P/AD11> at ata0-slave UDMA33
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted
WARNING: R/W mount of / denied.  Filesystem is not clean - run fsck
WARNING: R/W mount of / denied.  Filesystem is not clean - run fsck
bge0: link state changed to UP
bge1: link state changed to UP
fxp0: link state changed to DOWN
fxp1: link state changed to DOWN
re0: link state changed to DOWN
bge1: link state changed to DOWN
bge0: link state changed to DOWN
bge1: link state changed to UP
bge0: link state changed to UP
pflog0: promiscuous mode enabled
bge0: link state changed to DOWN
bge0: link state changed to UP
bge0: link state changed to DOWN
bge1: link state changed to DOWN
bge0: link state changed to UP
bge1: link state changed to UP
bge1: link state changed to DOWN
bge1: link state changed to UP
WARNING: pseudo-random number generator used for IPsec processing

Offline wallabybob

  • Hero Member
  • *****
  • Posts: 5262
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #12 on: June 15, 2008, 01:25:36 am »
Pleased you have things working.

In the FreeBSD 6.2 dmseg output I was looking for something like the line
Quote
pci4: <network, ethernet> at device 0.0 (no driver attached)
but unfortunately my eyes passed right over it yesterday and went straight to it today.  :( This line says there is a PCI ethernet controller that no driver in the kernel recognises as a device it can control. Now that you have run the FreeBSD 6.3 based version its clear this was the Broadcom 5754 which was not supported in FreeBSD 6.2.

Offline David_W

  • Full Member
  • ***
  • Posts: 132
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #13 on: June 15, 2008, 01:49:38 am »
This is all as expected. There was an attempt to support the BCM5754 in FreeBSD 6.2, but it was realised relatively late in the process that the support wasn't complete and it needed to be yanked. FreeBSD 6.2-RELEASE won't recognise a BCM5754 at all.

Later on, full support for the BCM5754 was committed - as can be seen in FreeBSD 6.3. It's good to know that you've got the controller going now.

Offline fastcon68

  • Sr. Member
  • ****
  • Posts: 593
  • Karma: +0/-0
    • View Profile
Re: Dell SC440
« Reply #14 on: June 15, 2008, 10:29:23 pm »
Seems to finally be working.  The performance seems to be good.  One thing to note,  I had snort working but it stopped, under 6.2 release 1.2.  I ran for a couple of hours on 6.3 and now has stopped.   The snort release is 2.7.0.1_4.

Overall it seems to be a very stable release.
RC